Pro-Form PFSY64390 Instrukcja Użytkownika

¨USERÕS MANUALModel No. PFSY64390Serial No. The serial number is found in thelocation shown below. Write theserial number in the space above.CAUTIONRe

1017. Press a 2Ó Square Inner Cap (28) into the top of aPress Arm (77). Press a 1Ó Inner Cap (76) into the indicated hole inthe Press Arm (77).Attach

1120. Wrap the Butterfly Cable (73) around a ÒVÓ-Pulley(27) in the direction shown. Attach the ÒVÓ-Pulley anda Large Cable Trap (32) to the bracket on

1223. Attach the Butterfly Cable (73) to the bracket on theRight Butterfly Arm (11) with a 3/8Ó x 1Ó Bolt (84) andtwo 3/8Ó Nylon Jam Nuts (63). Note:

1327. Attach the bolt at the end of the Weight Cable (72),the 1/2Ó Plain Nut (107), the 1/2Ó Flat Washer (86),and the Long Weight Spacer (98) to the W

1430. Remove both 3 1/2Ó Pulleys (24) and the Cable Trap(25) from the pre-assembled Pulley Plates (23).Wrap the High Cable (73) around a 3 1/2Ó Pulley

1534. Wrap the Low Cable (75) around a 3 1/2Ó Pulley (24)in the direction shown. Attach the Pulley and a CableTrap (25) to the indicated hole in the B

163775575052437. Note: For the sake of clarity, the weights are notshown in the following steps.Wrap the Low Cable (75) around a 3 1/2Ó Pulley (24)in

1740. Wrap the Low Cable (75) around a 3 1/2Ó Pulley (24)in the direction shown. Attach the Pulley to the indi-cated bracket on the Press Base (6) wit

1843. Route the Low Cable (75) through the hole in thecenter of the Press Frame (8). Wrap the Low Cablearound a 3 1/2Ó Pulley (24) in the direction sh

1947. Route the Low Cable (75) through the hole in thecenter of the Press Frame (8). Attach the Low Cableto the indicated hole in the Leg Lever (41) w

2Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20Seat Assembly50. Press a 1Ó x 2Ó Inner Cap (83) into each end of aBackrest Adjustment Frame (70). Press a 1 1/4Ó InnerCap (35) into the indicated tu

52. Attach the Curl Pad (91) to the welded plate on theButterfly Front Leg (3) with two 1/4Ó x 3/4Ó Bolts (49).524991353. Press a 1Ó x 2Ó Inner Cap (8

2256. Make sure that all parts are properly tightened. The use of the remaining parts will be explained in ADJUST-MENT, beginning on page 25 of this m

23Cable DiagramsThe cable diagrams below and on the next page show the proper routing of the Butterfly Cable (73), the HighCable (74), the Low Cable (

24Low Cable (75)3845112 71012141513169

25Adjusting the Butterfly Backrest, Butterfly Seat, orPress BackrestTo adjust the Press Backrest (99), pull out the handle ofthe Adjustment Knob (78)

26Tightening the CablesWoven cable, the type of cable used on the home gym,can stretch slightly when it is first used. If there is slack inthe cables

27Leg High Arm Ab Low ButterflyWeight Raise Pulley Press Pulley Pulley ArmsPlates (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) (lbs.)Top 40 21 28 18 25 281 5

3/8" Nylon Locknut (50)3/8" Nylon Jam Nut (63)5/16" Nylon Locknut (64)1Ó Tap Screw (80)1/4" Flat Washer (71)3/8" Flat Washer

3/8" x 3 1/2" Bolt (56)3/8" x 4 3/4" Bolt (60)3/8" x 2 3/4" Bolt (46)3/8" x 3 3/4" Bolt (59)3/8" x 8"

3ASSEMBLED DIMENSIONS: Height: 78 in.Width: 78 in. Depth: 60 in. Low PulleyStationFoot PlateCurl PadPress ArmsSeatBackrestButterfly ArmsWARNINGDECALWA

1" Inner Cap (76)Retainer Ring (31)1" Round Outer Cap (38)1Ó x 2" Inner Cap (83)1 1/4" Square Inner Cap (35)3/4" Round Inner

Part ListÑModel No. PFSY64390 R1199AKey No. Qty. Description Key No. Qty. Description1 1 Butte

245024565250561004848825259292 28288930304363758064363030434243896476288964774836366464642447744748635948606324258924575059244850645089285674244863545

Ordering Replacement PartsLimited WarrantyTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondayt

4Note: This introduction will save you moretime than it takes to read it!Identifying PartsTo help you identify the small parts used in assem-bly, we h

1. Before beginning, make sure that you have readand understood the information on page 4.Locate and open the parts bag labeled ÒFRAMEASSEMBLY.ÓPress

3. Place the bracket on the lower end of the ButterflyUpright (1) over the indicated 5/16Ó x 2 1/2Ó CarriageBolts (92) in the Butterfly Base (4). Hand

7. Place the bracket on the lower end of the PressUpright (2) over the indicated 5/16Ó x 2 1/2Ó CarriageBolts (92) in the Press Base (6). Hand tighte

10. Press a 2Ó Square Inner Cap (28) into the each of thePress Top Frame (9). Attach the Press Top Frame (9) to the indicatedbracket at the top of the

914. Attach the Weight Top Frame (66) to the Press TopFrame (9) with two 5/16Ó x 2 3/4Ó Bolts (89), aSupport Plate (94), and two 5/16Ó Nylon Locknuts(